Parameters

Size: 24*45*95mm
Output Mode: RTC/VW/VT(Ti, Ni, SS316)/Bypass/TCR(M1, M2, M3)
Output Wattage: 1-80W
Resistance range: 0.05 - 1.5ohm for VT mode; 0.1 - 3.5ohm for VW/Bypass mode
Temperature range: 200~600℉ or 100~315℃
Battery Capacity: 2100mAh
E-juice Capacity: 3.5ml & 2.0ml
Colors: black, gold, red, silver, white

Joyetech eGrip 2 Kit comes with

• 1 x eGrip II
• 1 x NotchCoil 0.25ohm DL.
• 1 x BF SS316 0.5ohm coil head DL.
• 1 x BF Clapton 1.5ohm coil head MTL.
• 1 x BF RBA M&L. (vertical rebuild)
• 1 x mouthpiece
• 1 x atomizer Adapter
• 1 x USB Cable
• 1 x Manual & Warranty Card

Simple packing. Customary Packing from the factory, the packing is subject to change without notice.

Features

Variable temperature control
Real time clock display & screen protection
Game mode and custom logo
All-in-one device with TFTA-Tank Technology
Notch coil head brings wonderful experience
Advanced dual battery protection
Eliquid illumination LED with 7 changeable colors
Firmware Upgradeable

Power on/off:
Press the fire button 5 times in quick succession to turn the device on.
In the same way, the device will be powered off after 5 presses.

Vaping: 
Hold the fire button and inhale through the mouthpiece. Release the Fire button and exhale.

Shift between VT/VW/Bypass/TCR Modes:
Press the fire button for three times to shift between diffferent Modes when the battery is on.
(1)under VW mode, it presents: battery life, ohm, voltage and wattage.
(2)under VT mode, it presents: battery life, ohm, wattage, temperature and mode (Ni/Ti).

Adjust the wattage/temperature:
Under VW mode, rotate the ring around the button clockwise or counterclockwise to increase or decrease the wattage (up to 80W); under VT mode, rotate the ring around the button clockwise or counterclockwise to increase or decrease the temperature (100-315℃/200-600℉).
Rotate the ring faster clockwise or counterclockwise for continuous three grades, the device automatically increase or decrease 0.1W/5℃(10℉) numerically.

Atomizer head replacement/refilling:
TFTA-Tank technology means Top Filling and Top Airflow. Coil replacement and juice fill can be achieved by removing the top section from the cup.

Apply the Atomizer Adapter
Unscrew the mouthpiece base, and screw the atomizer adapter tightly with a tool (coin), then you can apply other types of atomizer with eGrip II.

Charging:

Plug into the charging port. It usually takes 2.5 hours to fully charge the battery via 1A wall adapter.

Indications:
1.Screen: The OLED screen presents time, watts, ohms, temperature, battery life and timing while vaping. 
2.No Atomizer Alert: When the coil is not installed properly, the screen will appear “No Atomizer”.
3.New Coil Alarm: When installing a new coil whose resistance is larger than the previous one to some degree, resetting the “basic resistance” (resistance at room temperature) shall be required.
After fitting a new coil, press the fire button while the atomizer base is removed to initiate a reset. After you reinstall the atomizer base with a new head, the screen will appear “new coil up, same down”. Rotate the regulation ring clockwise to confirm that a new coil has been fitted.
Should you see this message for any other reason, especially when reinstalling the same coil that is still warm after use. If so, rotate the regulation ring counterclockwise so that the ‘basic resistance” won’t be reset.
4.Device Too Hot Alert: When the device’s inner temperature passes over 70℃, the output will shut off automatically and the screen will appear “Device Too Hot” for 5 seconds. After then, it switches back to normal.
5.Temperature Protection: Under VT mode, if the coil’s actual temperature reaches to the set temperature, the device will show “Temp Protection”. 
6.Over 10s Protection: If you keep pressing the fire button for more than 10 seconds, the screen will appear “Over 10S”.
7.Atomizer Short-circuit Protection: When atomizer short-circuit occurs, the screen will appear “Atomizer Short”.
8.Atomizer Low Alert: When the atomizer resistance is lower than 0.1ohm under VW mode or lower than 0.05ohm under VT mode, “Atomizer Low” will appear on the screen.
9.Low-voltage Protection: When the battery voltage is lower than 3.3V, the screen will appear “Battery Low” and “Lock”. Thus the battery is locked. Recharging to unlock the battery.

Note:
1. Under VT mode, please install the temperature control coils at room temperature ;
2. Only use temperature control coils under VT mode. Damages will be caused when temperature control coils are accidentally used under VW mode.
3. VT mode only supports a maximum of 1.5ohm. It will automatically switch to VW mode when the coil is larger than 1.5ohm or using a normal coil under VT mode.

• eGrip 2 Kit doesn't come with e-liquids. You shall purchase e-liquids separately.
• There is CE mark on battery end.
• You can download certificates.
• 0.25 ohm 코일 사용시엔  튐 증상이 있을 수 있습니다. 모드기기 전용 액상을 사용해주세요.